ELPEGUARD® conformal coatings
ELPEGUARD® conformal coatings are used to protect and insulate assembled pcbs so that they can fulfil higher requirements regarding reliability and service life.
ELPEGUARD® Thin film coatings
Solvent-containing or aqueous 1- and 2-pack ready-to use systems with very good resistance against moisture and condensation, thus enabling an excellent corrosion protection for assembled pcbs (e.g. e-corrosion and migration), typical dry layer thickness < 80 µm, suitable for coating flexible circuits (“flex-to-install”); can be soldered through for repair or removed mechanically (blasting method); coloured-transparent, opaque or fluorescent adjustments permit a simple checking of the coating layer for completeness by daylight or UV light (black light)
ELPEGUARD® SL 1800 Family
- Base: acrylate resins (AR)
- physical drying
- very good TST resistance (thermal shock test) from -40 to 150 °C or -65 °C to +125 °C, respectively
- good wetting of silicone-contaminated surfaces with conformal coatings of the series ELPEGUARD® SL 1801 FLZ
- can be completely removed for repair by means of product-specific thinner
- auxiliary products recommended: Cleaning agent R 5817 and cleaning agent R 5888 (for cleaning product carriers)
- Application: Brushing, Spraying, Dipping, and Selective coating methods
- Curing: curing at room temperature and thermal curing
- Temp: - 65 to + 125/150 °C
- Applications: aerospace, consumer, e-mobility / automotive, industrial, renewables, satellite and communication technology
ELPEGUARD® SL 1307 Family
- base: acrylate resins (AR)
- rapid drying at room temperature
- good yellowing resistance
- can be completely removed for repair by means of product-specific thinner
- protects against corrosive gases at highest severity level GX acc. to Isa-71.04
- auxiliary product recommended: Cleaning agent R 5817
- Application: Brushing, Spraying, Dipping, Selective coating methods, and Spraycan
- Curing: curing at room temperature and thermal curing
- Temp: - 65 to + 125/150 °C
- Standards: UL 94, UL 746E, IPC-CC-830B, MIL-I-46058C, and IEC 61086
- Applications: aerospace, consumer, e-mobility / automotive, industrial, lighting, medical, renewables, satellite and communication technology, security / defense
ELPEGUARD® SL 1301 ECO-FLZ series
- base: modified polyurethane resins (UR)
- SL 1301 ECO-BA-FLZ and SL 1301 ECO-FLZ/9 series: particularly uncritical in drying below components thanks to special composition of solvents
- free from aromatic solvents such as benzene, toluene, xylene and C9 aromates
- auxiliary product recommended: Cleaning agent R 5817, cleaning agent R 5888
- Application: Brushing, Spraying, Dipping, and Selective coating methods
- Curing: curing at room temperature and thermal curing
- Temp: - 40 to + 140 °C
- Standards: UL 94
- Applications: aerospace, consumer, e-mobility / automotive, industrial, renewables, satellite and communication technology, security / defense
ELPEGUARD® SL 1305 AQ-ECO series
- base: polyurethane resins (UR)
- aqueous, free from NMP, no odour when processed
- rapid drying at room temperature
- good yellowing resistance
- auxiliary product recommended: Cleaning agent R 5817
- Application: Brushing, Spraying, Dipping, and Selective coating methods
- Curing: curing at room temperature and thermal curing
- Temp: - 40 to + 130 °C
- Standards: UL 746E
- Applications: aerospace, consumer, e-mobility / automotive, industrial, lighting, renewables, satellite and communication technology, security / defense
ELPEGUARD® SL 1347
- base: acrylate resins (AR)
- rapid drying at room temperature
- black-opaque, for strong contrast between LED and non-reflectant base material (of particular benefit in visual LED applications such as display panels etc.)
- auxiliary product recommended: Cleaning agent R 5817
- Application: Brushing, Spraying, and Selective coating methods
- Curing: curing at room temperature and thermal curing
- Temp: - 65 to + 125 °C
- Standards: not applicable
- Applications: aerospace, consumer, industrial, lighting, renewables, satellite and communication technology, security / defense
ELPEGUARD® UTC 1507 FLZ
- base: synthetic rubber (SC)
- permelastic from -65 to +150 °C
- low permeability to water vapour and low absorbance of moisture
- very good electrical insulation properties even under moisture, similar to those of silicones
- protects against corrosive gases at highest severity level GX acc. to ISA-71.04
- auxiliary product recommended: Cleaning agent R 5817 and cleaning agent R 5888 (for cleaning product carriers)
- Application: Brushing, Spraying, Dipping, and Selective coating methods
- Curing: curing at room temperature and thermal curing
- Temp: - 65 to + 150 °C
- Standards: UL 94
- Applications: aerospace, consumer, e-mobility / automotive, industrial, satellite and communication technology
ELPEGUARD® SL 9407 FLZ series
- base: 2-pack polyurethane resin (UR)
- high resistance against external influences, protect against corrosive gases at highest severity level GX acc. to ISA-71.04
- fungus resistant acc. to. RTCA DO-160G
- cold-flexible along with good adhesion, high thermal shock resistance even with 1000 µm layer thickness
- > 50 % of renewable raw materials
- low solvent emissions (< 5 %)
- auxiliary product recommended: Cleaning agent R 5817
- Application: Brushing, Spraying, and Selective coating methods
- Curing: curing at room temperature and thermal curing
- Temp: - 65 to + 125 °C
- Standards: not applicable
- Applications: aerospace, consumer, e-mobility / automotive, industrial, satellite and communication technology
ELPEGUARD® Thick film coatings
solvent-free 1-pack systems with excellent chemical resistance; typical dry layer thickness > 80 µm, thus providing excellent protection even in critical weather conditions; the fluorescent adjustment permits an easy and reliable check of the coating result under UV light (black light), can be removed mechanically for repair purposes
ELPEGUARD® UV Twin-Cure® DSL 1600 E-FLZ series
- base: copolymerisate of polyurethane (UR) and polyacrylate (AR)
- powerful protection through electrical insulation properties directly after UV curing
- chemical crosslinking in shadow areas
- protects against corrosive gases at highest severity level GX acc. to ISA-71.04
- excellent mechanical resistance
- auxiliary product recommended: Cleaning agent R 5817
- Application: Brushing, Selective coating methods, and Dispensing
- Curing: UV curing
- Temp: - 65 to + 130/145 °C
- Standards: UL 94, UL 746E, IPC-CC-830B, and MIL-I-46058C
- Applications: aerospace, consumer, e-mobility / automotive, industrial, lighting, renewables, satellite and communication technology, security / defense
ELPEGUARD® UV-LED Twin-Cure® DSL 1602 FLZ/400
- base: copolymerisate of polyurethane (UR) and polyacrylate (AR)
- for curing with UV LEDs
- chemical crosslinking in shadow areas
- fungus resistant acc. to. RTCA DO-160G
- auxiliary product recommended: Cleaning agent R 5817
- Application: Brushing, Selective coating methods, and Dispensing
- Curing: UV curing
- Temp: - 65 to + 130 °C
- Standards: UL 94
- Applications: consumer, e-mobility / automotive, industrial, satellite and communication technology
ELPEGUARD® UV Twin-Cure® DSL 1707 FLZ
- base: silicone (SR)
- good adhesion on all common base materials without adding grip agent (self-priming)
- powerful protection through electrical insulation properties directly after UV curing
- chemical cross-linking reaction in shadow zones (condensation cross-linking)
- enables the micro-encapsulation of small components
- high thermal shock resistance from -40 to +180 °C even in high layers
- stress-compensating under thermal shocks and vibrations
- auxiliary products recommended: Cleaning agents R 5807 and R 5817
- Application: Brushing, Selective coating methods, and Dispensing
- Curing: UV curing
- Temp: - 65 to + 200 °C
- Standards: UL 746E
- Applications: aerospace, consumer, e-mobility / automotive, industrial, lighting, renewables, satellite and communication technology, security / defense
ELPEGUARD® DSL 1705 FLZ
- base: silicone (SR)
- good adhesion on many common base materials without the addition of grip agent (self-priming)
- addition crosslinking, thus suitable for a use in encapsulated environments
- rapid thermal curing (10 min at 100 °C)
- stress-compensating under thermal shocks and vibrations
- auxiliary product recommended: Cleaning agent R 5817
- Application: Brushing, Dipping, and Selective coating methods
- Curing: thermal curing
- Temp: - 40 to + 200 °C
- Standards: UL 94 and UL 746E
- Applications: aerospace, consumer, e-mobility / automotive, industrial, lighting, medical, renewables, security / defense
ELPEGUARD® DSL 1706 FLZ series
- base: silicone (SR)
- good adhesion on many common base materials without addition of a grip agent (self-priming)
- stress-compensating under thermal shocks and vibrations
- rapid condensation crosslinking at room temperature
- Cleaning agents R 5807 and R 5817
- Application: Brushing, Spraying, and Selective coating methods
- Curing: curing at room temperature
- Temp: - 40 to + 200 °C
- Standards: not applicable
- Applications: aerospace, consumer, e-mobility / automotive, industrial, lighting, medical, renewables, satellite and communication technology, security / defense
ELPEGUARD® Gels for dam-and-fill applications
thixotropic gels for dam-and-fill applications, ideally suited for a simple and high-definition application of dams around connectors, components and contact pads to limit the application area of a subsequent conformal coating; available in cartridges
ELPEGUARD® Gel SL 1307 FLZ-T series
- base: acrylate resins (AR)
- thixotropic and highly thixotropic adjustments
- physical drying
- no intermediate drying necessary for conformal coating
- auxiliary products recommended: Cleaning agent R 5817, dosing accessories for cartridge application
- Application: Dispensing
- Curing: curing at room temperature and thermal curing
- Standards: UL 94
- Applications: consumer, e-mobility / automotive, industrial, lighting, railway, satellite and communication technology, security / defense
ELPEGUARD® Dam-and-Cure GEL 1602 FLZ-UV
- Base: acrylate resins (AR)
- when using ELPEGUARD® thick film coatings of the series UV-LED Twin-Cure® and UV Twin-Cure®, curing can be carried out together with the GEL 1602 FLZ-UV (without intermediate curing)
- auxiliary products recommended: Cleaning agent R 5817 and cleaning agent R 5888 (for cleaning product carriers), dosing accessories for cartridge application
- /
Featured
Neuauflage des Fachbuchs
"Beschichtungsstoffe für die Elektronik - Schutzlacke und Vergussmassen"
